The Silver Pulser is housed in an attractive new custom plastic box, with a built-in compartment for the 9 Volt battery. A slide-off lid allows you to change the battery easily. A Thumbwheel Switch Control Knob turns the Silver Pulser on and off and varies the intensity of the "Bio-Stimulator Probe" output. A Green LED Light comes on when the Silver Pulser is turned on. Flashing Yellow LED light on the unit indicates there is a correct "Bio-Stimulator" output and comes on only when current is flowing. Red LED Light indicates low battery. In addition, an Orange LED light is used for the Ionic-Colloidal Silver generation. The Orange LED Light comes on when current through Silver Wires is correct.

The Silver Pulser has one 6 pin DIN style jack for plugging in the Fine Silver Wires, another for the Stimulator Probes. A second jack is used for hooking up an AC-DC Wall Adaptor so you don't have to go through batteries when making Ionic colloidal silver. We also include Cotton Sleeves to put over the Bio-Stimulator Probes for helping to maintain a good connection when moistened. The Silver Pulser is packaged in a custom soft carrying case for easy storage.

Each Silver Pulser is a professionally designed quality instrument, thoroughly tested on an oscilloscope and is guaranteed to operate as per the specifications in Dr. Bob Beck's research.  The Silver Pulser is a dual-function instrument, being both a Bio-Pulser / Zapper and Ionic Colloidal Silver Generator.  The Silver Pulser generates the finest quality Ionic Colloidal Silver at a rate of 5-8 ppm (part per million) in 20 minutes per 16 ounces of distilled water, with an Ionic Colloidal Silver particle size that is mostly ions, with colloidal particles in the range of 0.005 - 0.015 microns (Verified on a Scanning Electron Microscope).  It has a Bi-Phasic output frequency of ~3.92 Hertz (cycles per second) at a nominal voltage of 31 volts DC peak per cycle.   Peak to peak voltage is 62 volts. Unit uses a single 9-volt battery. The Silver Pulser circuit board is gold plated for the highest quality and performance. All solders and fluxes are food-grade for highest safety and purity.
 
 

Making high-quality colloidal silver is now easier than ever.  The Silver Pulser comes with a custom retainer that is placed on top of your glass of water or other container.  The silver wires extend straight down into the water and are held in place by a spring-loaded clip.  Silver wire length is adjustable to fit the depth of your glass or container.  The silver wires are easy to remove and replace.  During the process of making colloidal silver, the positive silver wire loses silver and gradually shrinks in diameter.  By switching the positive and negative wires around, the usable life of the wires is doubled and you can make twice the amount of colloidal silver.

Silver Pulser Specifications

* Battery voltage: 9 volts DC (alkaline battery)
* Optional Input voltage: 6-12 volts DC @500mA wall transformer/adaptor, auto battery or solar panel
* Output voltage at colloidal silver wires: 31 Volts DC (+/- 1 Volt) constant voltage
* Output current at colloidal silver wires: 1.5 milliamps (+/- 0.5ma.) constant current output
* Output voltage at stimulator probes: 31 volts (peak per cycle, 62 volts peak-peak)
* Output current at stimulator probes: ~12 mA max. when probes shorted and control knob at full intensity
* Bi-phasic at ~3.92 Hertz +/- 1 Hz
* Ionic colloidal silver production: 5-8 parts per million in two hours in 16 ounces of distilled water
* Ionic colloidal silver particle size: mostly ionic with colloidal particles in the range of 0.005 to 0.015 microns
* Ionic colloidal silver color: clear or pale gold when made as directed
* Silver Probes can make many gallons of 5 to 8 parts per million colloidal silver when used as directed
* One standard 9-volt alkaline battery (included)
* Three Year Parts and Labor Warranty

The fine Silver Wires are 14 AWG (1.63mm or 0.064" dia.) x 8" long (20cm) constructed of .9999 pure silver